7 NHTSA safety recall campaigns were found for the 1979 Ford Club Wagon.
Component: WHEELS
Recall date: 1979-08-07
THE WHEEL ASSEMBLY MAY CONTAIN SUBSTANDARD WELDS IN THE AREA WHERE THE DISC IS ATTACHED TO THE RIM. AS A RESULT, CRACKS CAN FORM IN THE WHEEL ASSEMBLY, CAUSING AIR LOSS AND AN UNDERINFLATED TIRE.
DEALER WILL INSPECT AND REPLACE ANY DEFECTIVE WHEELS WITHOUT CHARGE TO OWNER.
Component: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS
Recall date: 1979-06-19
CERTAIN VEHICLES MAY NOT CONTAIN THE SPECIFIED BODY MOUNTED HEAT SHIELDS. THIS COULD CAUSE HIGH FLOOR PAN TEMPERATURES WHEN THE ENGINE IS IDLED FOR EXTENDED PERIODS OF TIME. FOULED SPARK PLUGS OR OTHER ENGINE CONDITIONS COULD FURTHER INCREASE EXHAUST TEMPERATURES.
THE DEALER WILL INSTALL THE NECESSARY FRAME MOUNTED HEAT SHIELD, IF MISSING.
Component: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS
Recall date: 1979-06-19
THE INCORRECTLY INSTALLED LEFT FRONT BRAKE HOSES MAY ALLOW FOR CONTACT BETWEEN THE FRONT BRAKE HOSES AND THE FRONT TIRES WHEN THE FRONT WHEELS ARE IN FULL RIGHT OR LEFT TURN POSITIONS. IF CONTACT IS MADE, THE HOSE COULD WEAR AND ALLOW BRAKE FLUID TO LEAK OUT.
THE DEALER WILL INSPECT FRONT BRAKE HOSES AND REPLACE THOSE LACKING THE PROPER CLEARANCE WITH CURRENT PRODUCTION HOSES, WITHOUT CHARGE TO OWNER.
Component: STEERING:GEAR BOX:SHAFT SECTOR
Recall date: 1978-12-21
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE STEERING GEAR ASSEMBLY OR INSTALL A NEW SECTOR SHAFT IN THE STEERING GEAR ASSEMBLY.
Component: POWER TRAIN:AUTOMATIC TRANSMISSION
Recall date: 1978-11-27
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE PARKING PAWL WITH ONE THAT HAS BEEN HEAT-TREATED.
Component: SEAT BELTS:REAR/OTHER
Recall date: 1978-10-05
ON THE INVOLVED VEHICLES, THE POTENTIAL EXISTS FOR THE OUTBOARD SEAT BELTS TO BECOME TRAPPED IN THE SEAT-BED PIVOTING MECHANISM. SHOULD THE BELT BECOME TRAPPED IN THE MECHANISM WHEN THE SEAT IS CONVERTED TO A BED, THE BELT MAY BECOME CUT OR FRAYED.
THE DEALER WILL INSTALL SEAT BELT SHIELDS ON THE FOLDING SEAT/BED PIVOTING MECHANISM AND REPLACE THE OUTBOARD SEAT BELT ASSEMBLIES IF DAMAGED, FREE OF CHARGE.
Component: POWER TRAIN:AUTOMATIC TRANSMISSION
Recall date: 1978-09-15
THESE TRANSMISSIONS MAY CONTAIN IMPROPERLY MANUFACTURED PARKING PAWL ACTUATING RODS. CONSEQUENTLY, THE UNHARDENED CAM SURFACE OF THESE RODS CAN ALLOW THE ROD TO DEFORM DURING USE WITH RESULTANT INCREASE IN SHIFT EFFORTS AND DIFFICULTY IN RELEASING THE PARKING PAWL AND ENGAGING THE PARKING GEAR.
DEALER WILL REPLACE THE TRANSMISSION PARKING PAWL ACTUATING ROD WITHOUT CHARGE TO OWNER.
Recall applicability can depend on VIN and production details. Confirm your specific vehicle with the manufacturer or the official NHTSA VIN recall lookup.